 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TS79L00 series 3-Terminal Low Current Negative Voltage Regulator Voltage Range - 5V to - 24V Output Current up to 100mA General Description The TS79L00 Series of negative voltage regulators are inexpensive, easy-to-use devices suitable for a multitude of applications that require a regulated supply of up to 100mA. Like their higher power TS7900 and TS79M00 Series cousins, these regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the TS79L00 devices in many applications. These devices offer a substantial performance advantage over the traditional zener diode-resistor combination, as output impedance and quiescent current are substantially reduced. This series is offered in 3-pin TO-92, SOT-89 and 8-pin SOP-8 package. Features Output current up to 100mA No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 4% tolerance Standard Application Ordering Information Part No. TS79LxxCT TS79LxxCY TS79LxxCS Note: Where xx denotes voltage option. -20 ~ +85 C o Operating Temp. (Ambient) Package TO-92 SOT-89 SOP-8 A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Pin Assignment Pin No. TS79L00CT 3 2 1 Pin TS79L00CS 1 2, 3, 6, 7 5 4, 8 TS79L00CY 3 2 1 Description Output Input Ground Non connected TS79L00 series 1-8 2003/12 rev. D Absolute Maximum Rating Input Voltage Input Voltage Power Dissipation TO-92 TO-89 SOP-8 Operating Junction Temperature Range Storage Temperature Range Note : * TS79L05 to TS79L18 ** TS79L24 TJ TSTG Pd Vin * Vin ** - 35 - 40 0.625 0.5 0.5 0 ~ +125 -65 ~ +150 o o V V W C C TS79L05 Electrical Characteristics (Vin= -10V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output voltage Symbol o Test Conditions Tj=25 C -7.5VVin -20V, 5mAIout100mA Min - 4.80 - 4.75 Typ -5 -5 Max - 5.20 - 5.25 Unit V Vout Line Regulation REGline Tj=25 oC o -7.5VVin -20V, Io=40mA 5mAIout100mA 5mAIout40mA o ------- 50 20 10 3 --40 49 1.7 0.15 150 60 30 6 1.5 0.1 ----uV dB V A mA mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq Iq Vn RR Vdrop Io peak Tj=25 C Iout=0, Tj=25 C -8VVin -20V 1mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -8VVin -18V Tj=25 C Tj=25 C o o o -41 --- Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS79L00 series 2-8 2003/12 rev. D TS79L06 Electrical Characteristics (Vin= -11V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Tj=25 oC Output voltage Vout Test Conditions Min - 5.76 - 5.70 Typ -6 -6 Max - 6.24 - 6.30 Unit -8.5VVin -21V, 5mAIout100mA V Line Regulation REGline Tj=25 oC o -8.5VVin -21V, Io=40mA 5mAIout100mA 5mAIout40mA o ------- 50 20 10 3 --40 49 1.7 0.15 150 60 30 6 1.5 0.1 ----uV dB V A mA mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq Iq Vn RR Vdrop Io peak Tj=25 C Iout=0, Tj=25 C -9VVin -21V 1mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -9VVin -19V Tj=25 C Tj=25 C o o o -41 --- TS79L08 Electrical Characteristics (Vin= -14V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output Voltage Symbol o Test Conditions Tj=25 C -10.5VVin -23V, 5mAIout100mA Min - 7.69 - 7.61 Typ -8 -8 Max - 8.32 - 8.40 Unit V Vout Line Regulation REGline Tj=25 oC o -10.5VVin -23V, Io=40mA 5mAIout100mA 5mAIout40mA ------- 80 25 10 3 --60 57 1.7 0.15 160 80 40 6 1.5 0.1 ----uV dB V A mA mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq lq Vn RR Vdrop Io peak Tj=25 C Iout=0, Tj=25 oC -11VVin -23V 1mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -13VVin -23V Tj=25 C Tj=25 C o o o -37 --- Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS79L00 series 3-8 2003/12 rev. D TS79L09 Electrical Characteristics (Vin= -15V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output Voltage Symbol o Test Conditions Tj=25 C -11.5VVin -24V, 5mAIout100mA Min - 8.65 - 8.57 Typ -9 -9 Max - 9.36 - 9.45 Unit V Vout Line Regulation REGline Tj=25 oC o -11.5VVin -24V, Io=40mA 5mAIout100mA 5mAIout40mA o ------- 90 30 15 3 --60 57 1.7 0.15 180 90 45 6 1.5 0.1 ----uV dB V A mA mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq lq Vn RR Vdrop Io peak Tj=25 C Iout=0, Tj=25 C -12VVin -24V 5mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -14VVin -24V Tj=25 C Tj=25 C o o o -37 --- TS79L12 Electrical Characteristics (Vin= -19V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output Voltage Symbol o Test Conditions Tj=25 C -14.5VVin -27V, 5mAIout100mA Min - 11.53 - 11.42 Typ - 12 - 12 Max - 12.48 - 12.60 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC o -14.5VVin -27V, Io=40mA 5mAIout100mA 5mAIout40mA ------- 120 40 20 3 --80 42 1.7 0.15 240 120 60 6.5 1.5 0.1 ----- mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq lq Vn RR Vdrop Io peak Tj=25 C, Iout=0 -16VVin -27V 5mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -15VVin -25V Tj=25 C Tj=25 C o o o mA -37 --- uV dB V A Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS79L00 series 4-8 2003/12 rev. D TS79L15 Electrical Characteristics (Vin= -23V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output Voltage Symbol o Test Conditions Tj=25 C -17.5VVin -30V, 5mAIout100mA Min - 14.42 - 14.28 Typ - 15 - 15 Max - 15.60 - 15.75 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC o -17.5VVin -30V, Io=40mA 5mAIout100mA 5mAIout40mA ------- 150 50 25 3 --90 39 1.7 0.15 300 150 75 6.5 1.5 0.1 ----- mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq lq Vn RR Vdrop Io peak Tj=25 C, Iout=0 -20VVin -30V 5mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -18VVin -28V Tj=25 C Tj=25 C o o o mA -34 --- uV dB V A TS79L18 Electrical Characteristics (Vin= -27V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output Voltage Symbol o Test Conditions Tj=25 C -21VVin- 33V, 5mAIout100mA Min - 17.30 - 17.14 Typ - 18 - 18 Max - 18.72 - 18.90 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC o -21VVin -33V, Io=40mA 5mAIout100mA 5mAIout40mA ------- 180 60 30 3 --150 48 1.7 0.15 360 180 90 6.5 1.5 0.1 ----- mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq lq Vn RR Vdrop Io peak Tj=25 C, Iout=0 -21VVin -33V 5mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -23VVin -33V Tj=25 C Tj=25 C o o o mA -33 --- uV dB V A Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS79L00 series 5-8 2003/12 rev. D TS79L24 Electrical Characteristics (Vin= -33V, Iout=40mA, 0 oCTj125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Output Voltage Symbol o Test Conditions Tj=25 C -27VVin -38V, 5mAIout100mA Min - 23.07 - 22.85 Typ - 24 - 24 Max - 24.96 - 25.20 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC -27VVin -38V, Io=40mA 5mAIout100mA 5mAIout40mA o ------- 200 80 40 4 --200 45 1.7 0.15 400 240 120 7 1.5 0.1 ----- mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current REGload Iq lq Vn RR Vdrop Io peak Iout=0, Tj=25 C -28VVin -38V 5mAIout40mA 10Hzf100KHz, Tj=25 C f=120Hz, -29VVin -35V Tj=25 C Tj=25 C o o o mA -31 --- uV dB V A Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS79L00 series 6-8 2003/12 rev. D TO-92 Mechanical Drawing A DIM TO-92 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 4.30 4.70 0.169 0.185 4.30 4.70 0.169 0.185 14.30(typ) 0.563(typ) 0.43 0.49 0.017 0.019 2.19 2.81 0.086 0.111 3.30 3.70 0.130 0.146 2.42 2.66 0.095 0.105 0.37 0.43 0.015 0.017 B C E F A B C D E F G H H D G SOT-89 Mechanical Drawing A B SOT-89 DIMENSION I DIM A B C D E F G H I J H G C E D J F MILLIMETERS MIN MAX 4.40 4.60 1.50 1.7 2.30 2.60 0.40 0.52 1.50 1.50 3.00 3.00 0.89 1.20 4.05 4.25 1.4 1.6 0.35 0.44 INCHES MIN MAX 0.173 0.181 0.059 0.070 0.090 0.102 0.016 0.020 0.059 0.059 0.118 0.118 0.035 0.047 0.159 0.167 0.055 0.068 0.014 0.017 TS79L00 series 7-8 2003/12 rev. D SOP-8 Mechanical Drawing A DIM SOP-8 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 4.80 5.00 0.189 0.196 3.80 4.00 0.150 0.157 1.35 1.75 0.054 0.068 0.35 0.49 0.014 0.019 0.40 1.25 0.016 0.049 1.27 (typ) 0.05 (typ) 0.10 0.25 0.004 0.009 0o 7o 0o 7o 5.80 6.20 0.229 0.244 0.25 0.50 0.010 0.019 16 9 B P 1 8 G C D K M R F A B C D F G K M P R TS79L00 series 8-8 2003/12 rev. D |
Price & Availability of TS79L24CY
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |